- #Toshiba e studio 452 brochure manual#
- #Toshiba e studio 452 brochure mac#
- #Toshiba e studio 452 brochure windows#
Regarding the recovery and disposal of the equipment, supplies, consumable parts, packing Their surface and whether they are properly stuck to the equipment.ĥ) Disposition of Consumable Parts, Packing Materials, Used batteries and IC-RAMs Power cord during service”, “Hot area”, “Laser warning label” etc. During servicing, be sure to check the rating plate and the cautionary labels such as “Unplug the Parts not recommended by Toshiba TEC Corporation. Instance, and may result in fatal accidents. If these parts are shorted circuit and/or made their functions out, they may burn down, for The breaker, door switch, fuse, thermostat, thermofuse, thermistor, batteries, IC-RAMs including Be very careful to treat the touch panel gently and never hit it. Unplug the power cable and clean the area around the prongs of the plug once a year or more.Ī fire may occur when dust lies on this area. Of the laser beam.Remove all watches, rings, bracelets, etc. Avoid exposure to laser radiation during servicing.Īvoid direct exposure to the beam.Do not insert tools, parts, etc. Use suitable measuring instruments and tools. When servicing the machines with the power turned ON, be sure not to touch live sections and
Be careful when removing the covers since there might be the parts with very sharp edges Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fan, etc. on them even after the power is turned OFF. Especially, the board of these components should not be touched since theĮlectric charge may remain in the capacitors, etc. High-voltage transformer, exposure lamp control inverter, inverter for the LCD backlight and Be sure not to touch high-voltage sections such as the chargers, developer, IH control circuit, Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the Basically, be sure to turn the main switch off and unplug the power cord during service. The socket-outlet shall be installed near the equipment and shall be easily accessible.īe sure to fix and plug in the power cable securely after the installation so that no one trips over To insure adequate working space for the copying operation, keep a minimum clearance of 80Ĭm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) in the rear. Select a suitable place for installation.Īvoid excessive heat, high humidity, dust, vibration and direct sunlight.Īlso provide proper ventilation as the equipment emits a slight amount of ozone. Never ground it to a gas pipe or a water pipe. The equipment must be grounded for safety. the control panel, ADU or RADF) when transporting the equipment.īe sure to use a dedicated outlet with AC 110V/13.2A, 115V or 127V / 12A, 220-240V or 240V /
The equipment is quite heavy and weighs approximately 83kg (182.98 lb.): e-STUDIO350/450 /Ĩ6kg (189.59 lb.): e-STUDIO352/353/452/453 therefore pay fullattention when handling it.īe sure not to hold the movable parts or units (e.g. When transporting/installing the equipment, employ two persons and be sure to use the positions The installation and service should be done by a qualified service GENERAL PRECAUTIONS REGARDING THE INSTALLATIONĪND SERVICE FOR e-STUDIO350/352/353/450/452/453 No patent liability is assumed, however, with respect to the use of the
#Toshiba e studio 452 brochure manual#
Under the copyright laws, this manual cannot be reproduced in any form without prior written permission © 2003 - 2007 TOSHIBA TEC CORPORATION All rights reserved
Other company names and product names in this manual are the trademarks of their respective Molykote is a registered trademark of Dow Corning Corporation. NOVELL, NetWare, and NDS are trademarks or registered trademarks of Novell, Inc. PostScript is a trademark of Adobe Systems Incorporated.
#Toshiba e studio 452 brochure mac#
Microsoft products are trademarks or registered trademarks of Microsoft Corporation in the U.S.Īpple, AppleTalk, Macintosh, and Mac are trademarks of Apple Computer, Inc.
#Toshiba e studio 452 brochure windows#
Microsoft, Windows, Windows NT, Windows Vista and the brand names and product names of other The official name of Windows XP is Microsoft Windows XP Operating System. The official name of Windows 2000 is Microsoft Windows 2000 Operating System. The official name of Windows Me is Microsoft Windows Millennium Edition Operating System. The official name of Windows 98 is Microsoft Windows 98 Operating System. The official name of Windows 95 is Microsoft Windows 95 Operating System.
0 kommentar(er)
